The principle of the incrementally launched bridge consists of building the superstructure segments in a casting yard located behind the bridge abutment. Each segment is matchcast against the previous one and prestressed to the section of superstructure already built. The entire superstructure is then jacked forward a distance equal to the length of this segment. This process is repeated until the bridge is in its final position. The secondary PT is then installed and the temporary bearings are replaced by the permanent bearings. This form of construction can be used for bridges having constant cross sectional shape throughout their length. The bridge should be straight or have a constant horizontal and vertical curvature.
This method, following a suitable technological design with aspects of the ILM method projected to the superstructure design, brings a wide range of advantages and is very effective compared to other methods, despite generally higher material demands. This is virtually a “factory” for bridge construction in segments with advantages like maximum productivity, reinforcement assemblages along the whole length of segment, minimum formwork and others.
Having considerable experiences in this technology, VSL offers and successfully provides the optimisation of the load bearing structure design and stabilisation of piers against effects of horizontal forces, if required, as well as the design of technological equipment for launching and casting yard, in cooperation with the designer and contractor and according to the scope of required works. Particularly the casting yard, with respect to the control of the load bearing structure’s geometry with minimum tolerances, and safe launching device are crucial for successful realisation of launching. The VSL´s concept of launching based on flexible casting yard and hydraulic strand units maximally reduces the risks associated with this method.
The scope of works offered by VSL, besides the participation in design, includes prestressing works, delivery of special sliding pot bearings convertible to permanent ones, delivery and operation of the launching equipemnt and additional hydraulics related, and lifting works necessary for replacement or conversion of sliding bearings.
The incremental launching method is applied mainly to structures with high piers or where the formwork on solid centring cannot be used (above the existing build-up area, communications, water areas, in ecologically sensitive areas, etc.)
ประกอบด้วยอาคารส่วนโครงสร้างส่วนบนในศอกหล่ออยู่หลัง abutment สะพานหลักของสะพานแบบเพิ่มหน่วยเปิด แต่ละเซกเมนต์จะ matchcast กับนี้ และอัดแรงไปยังส่วนของโครงสร้างส่วนบนที่สร้างขึ้นแล้ว โครงสร้างส่วนบนทั้งหมดเป็น jacked แล้วส่งต่อเป็นระยะทางเท่ากับความยาวของส่วนนี้ กระบวนการนี้ซ้ำจนกว่าสะพานจะในตำแหน่งสุดท้าย PT รองแล้วติดตั้ง และปืนชั่วคราวจะถูกแทนที่ โดยปืนถาวร สามารถใช้แบบฟอร์มนี้การก่อสร้างสำหรับสะพานที่มีรูปร่างตัดข้ามคงที่ตลอดความยาวของ สะพานควรจะตรง หรือโค้งแนวนอน และแนวตั้งคงได้วิธีการนี้ ต่อไปนี้การออกแบบเทคโนโลยีที่เหมาะสมกับด้านของวิธีการ ILM คาดว่าจะออกแบบโครงสร้างส่วนบน นำประโยชน์ที่หลากหลาย และมีประสิทธิภาพมากเมื่อเทียบกับวิธีอื่น ๆ แม้มีความต้องการวัสดุโดยทั่วไปสูง นี่คือ "โรงงาน" การก่อสร้างสะพานในเซ็กเมนต์ ด้วยประโยชน์เช่นประสิทธิภาพ assemblages เหล็กเสริมตามยาวทั้งเซ็กเมนต์ แบบหล่อขั้นต่ำ และอื่น ๆHaving considerable experiences in this technology, VSL offers and successfully provides the optimisation of the load bearing structure design and stabilisation of piers against effects of horizontal forces, if required, as well as the design of technological equipment for launching and casting yard, in cooperation with the designer and contractor and according to the scope of required works. Particularly the casting yard, with respect to the control of the load bearing structure’s geometry with minimum tolerances, and safe launching device are crucial for successful realisation of launching. The VSL´s concept of launching based on flexible casting yard and hydraulic strand units maximally reduces the risks associated with this method.The scope of works offered by VSL, besides the participation in design, includes prestressing works, delivery of special sliding pot bearings convertible to permanent ones, delivery and operation of the launching equipemnt and additional hydraulics related, and lifting works necessary for replacement or conversion of sliding bearings.The incremental launching method is applied mainly to structures with high piers or where the formwork on solid centring cannot be used (above the existing build-up area, communications, water areas, in ecologically sensitive areas, etc.)
การแปล กรุณารอสักครู่..