Since no pellet moisture higher than 10 wt.% is allowed by EN
14961-2 for ENPlus classification, it was not necessary to test with
other moistures at the inlet. Moreover, Serrano et al. [9] observed that
both, very low(below 8 wt.%) and very high (depending on thematerial)
moisture content, are inadequate for a good compaction.
Regarding the effect of the inlet moisture content on durability and
bulk density parameters, three moisture contents (Mm) were tested
in PO100 (15, 17, 19 wt.%), PO45PI55 (12, 17, 18 wt.%) and PO5PI95
(26, 33, 37wt.%) blends,with compression dies of 17, 19 and 21mm, respectively
(Fig. 3). As a result, different trends were observed between
the inlet moisture content and the durability and bulk density in the
three blends studied.
For PO100, an increase in durability and bulk density was observed
Since no pellet moisture higher than 10 wt.% is allowed by EN14961-2 for ENPlus classification, it was not necessary to test withother moistures at the inlet. Moreover, Serrano et al. [9] observed thatboth, very low(below 8 wt.%) and very high (depending on thematerial)moisture content, are inadequate for a good compaction.Regarding the effect of the inlet moisture content on durability andbulk density parameters, three moisture contents (Mm) were testedin PO100 (15, 17, 19 wt.%), PO45PI55 (12, 17, 18 wt.%) and PO5PI95(26, 33, 37wt.%) blends,with compression dies of 17, 19 and 21mm, respectively(Fig. 3). As a result, different trends were observed betweenthe inlet moisture content and the durability and bulk density in thethree blends studied.For PO100, an increase in durability and bulk density was observed
การแปล กรุณารอสักครู่..
ตั้งแต่เม็ดความชื้นไม่สูงกว่า 10 น้ำหนัก.% ที่ได้รับอนุญาตโดย EN
14961-2 สำหรับการจำแนก ENPlus มันก็ไม่จำเป็นที่จะต้องมีการทดสอบ
ความชื้นอื่น ๆ ได้ที่ทางเข้า นอกจากนี้ Serrano, et al [9] ตั้งข้อสังเกตว่า
ทั้งสองที่ต่ำมาก (ต่ำกว่า 8 น้ำหนัก.%) และสูงมาก (ขึ้นอยู่กับ thematerial)
ความชื้นไม่เพียงพอสำหรับการบดอัดที่ดี.
เกี่ยวกับผลกระทบของปริมาณความชื้นเข้ากับความทนทานและ
ความหนาแน่นพารามิเตอร์สาม ความชื้น (mm) ได้มีการทดสอบ
ใน PO100 (15, 17, 19 โดยน้ำหนัก.%) PO45PI55 (12, 17, 18 โดยน้ำหนัก.%) และ PO5PI95
(26, 33, 37wt.%) ผสมผสานกับการบีบอัดตาย 17 19 และ 21mm ตามลำดับ
(รูปที่. 3) เป็นผลให้แนวโน้มที่แตกต่างกันถูกตั้งข้อสังเกตระหว่าง
ความชื้นเข้าและความทนทานและความหนาแน่นใน
สามผสมศึกษา.
PO100 สำหรับการเพิ่มความทนทานและความหนาแน่นเป็นที่สังเกต
การแปล กรุณารอสักครู่..
เนื่องจากไม่มีเม็ดความชื้นสูงกว่า 10 % โดยน้ำหนักที่ได้รับอนุญาตโดย EN
14961-2 การจำแนก enplus มันไม่จำเป็นที่จะทดสอบกับ
ความชื้นอื่น ๆที่ทางเข้า นอกจากนี้ เซอราโน และคณะ [ 9 ] 8
ทั้งต่ำมาก ( ต่ำกว่า 8 % โดยน้ำหนัก ) และสูงมาก ( ขึ้นอยู่กับการ )
ความชื้นไม่เพียงพอสำหรับการบดอัดดี
เกี่ยวกับผลของความชื้นต่อความทนทานและ
ปากน้ำพารามิเตอร์ความหนาแน่น 3 ความชื้น ( มม. ) ทดสอบ
ใน po100 ( 15 , 17 , 19 % โดยน้ำหนัก ) , po45pi55 ( 12 , 17 , 18 % โดยน้ำหนัก ) และ po5pi95
( 26 , 33 , 37wt % ) ผสมกับการบีบอัดตาย 17 , 19 และ 21 ตามลำดับ
( รูปที่ 3 ) เป็นผลให้แนวโน้มที่แตกต่างกันที่พบระหว่าง
ฝุ่น ความชื้น และความคงทนและความหนาแน่นใน
สำหรับ po100 สามผสม , ศึกษาเพิ่มความทนทานและความหนาแน่นสูง
การแปล กรุณารอสักครู่..