2. Biomass conversion technologies
A number of conversion schemes have been developed to capitalize on biomass feed properties and reviewed (Czernik and Bridgwater, 2004 and Mohan et al., 2006). Both biological (anaerobic digestion, hydrolysis and fermentation) and thermal (combustion, pyrolysis, liquefaction, torrifaction and gasification) methods are used for biomass conversion into fuel and byproducts. Only thermal processes to produce adsorbent chars are covered here. Biochar from thermal treatment also has a high energy density (typically >28 kJ/g).
3. Biomass prolysis
Pyrolysis is the thermal decomposition of materials in the absence of oxygen or when significantly less oxygen is present than required for complete combustion (Fig. 1, Table 1). Pyrolysis should be differentiated from gasification where biomass is reacted with steam, or air. Gasification converts biomass into syngas by careful control of the oxygen amount present. Pyrolysis covers a range of thermal decomposition processes and is difficult to precisely define. The older literature equates pyrolysis to carbonization where char (charcoal) is the principal product (Fig. 1, Table 1). Today, pyrolysis often describes processes in which liquids (biooils) are preferred products. Liquid production is favored in short pyrolysis times (fast pyrolysis). Conventional (slow) or fast (flash) pyrolysis depend upon the operating conditions used (temperature, heating rate and vapor residence time) (Czernik and Bridgwater, 2004 and Mohan et al., 2006). The feed’s heating rate, residence time and pyrolysis temperature distinguish the pyrolysis processes. Conventional pyrolysis is slow. The terms slow and fast pyrolysis are somewhat arbitrary and not precisely defined. Many pyrolyses have been performed at rates that are not “fast” or “slow” but are in a broad range between these extremes. A key point is whether or not vapors and aerosol components are rapidly removed to optimize liquid formation (fast pyrolysis, flash vacuum pyrolysis) or remain in contact with the solid, undergoing secondary reactions which produce added carbonaceous solids. Operating parameters for slow and fast pyrolysis to biochars are briefly discussed below.
2 . เทคโนโลยีการแปลงชีวมวล
จำนวนรูปแบบการแปลงได้รับการพัฒนาเพื่อใช้ประโยชน์จากคุณสมบัติป้อนชีวมวลและตรวจสอบ ( และ czernik Bridgwater 2004 และ Mohan et al . , 2006 ) ทั้งทางชีวภาพ ( anaerobic ย่อยอาหาร การย่อยและการหมัก ) และความร้อน ( การเผาไหม้ , ไพโรไลซิส , , ,torrifaction และก๊าซ ) วิธีการที่ใช้สำหรับการแปลงชีวมวลเป็นเชื้อเพลิงและผลิตภัณฑ์ที่ไม่ต้องการ แต่กระบวนการผลิตสารดูดซับความร้อนตัวอักษรครอบคลุมที่นี่ ไบโอชาร์จากการใช้ความร้อนยังมีความหนาแน่นพลังงานสูง ( โดยทั่วไป > 28 กิโลจูล / กรัม )
3 prolysis
ชีวมวลไพโรไลซิส คือความร้อนการสลายตัวของวัสดุในการขาดออกซิเจนหรือออกซิเจนเมื่อน้อยกว่าปัจจุบันกว่าที่จำเป็นสำหรับการเผาไหม้ที่สมบูรณ์ ( รูปที่ 1 ตารางที่ 1 ) ไพโรควรจะแตกต่างจากก๊าซชีวมวล คือ ที่ทำปฏิกิริยากับไอน้ำหรืออากาศ การผลิตก๊าซชีวมวลเป็นแก๊สแปลงโดยการควบคุมระวังออกซิเจนปริมาณปัจจุบันไพโรไลซิสที่ครอบคลุมช่วงของกระบวนการความร้อนการสลายตัวและเป็นเรื่องยากที่จะแม่นยำกำหนด เก่า วรรณกรรมเป็นถ่านที่ชาร์ถ่านลิกไนต์ไปเป็นผลิตภัณฑ์หลัก ( รูปที่ 1 ตารางที่ 1 ) วันนี้ ไพโร มักอธิบายกระบวนการที่ของเหลว ( biooils ) เป็นผลิตภัณฑ์ที่ต้องการ การผลิตของเหลวเป็นที่ชื่นชอบในเวลาไพโรสั้น ( ไพโรไลซิสแบบเร็ว )ปกติ ( ช้า ) หรือเร็ว ( แฟลช ) ไพโรขึ้นอยู่กับสภาวะ ( อุณหภูมิ อัตราการใช้ความร้อนและเวลาพัก ( ไอน้ำ ) และ czernik Bridgwater 2004 และ Mohan et al . , 2006 ) อัตราความร้อนของอาหาร ระยะเวลาและอุณหภูมิแยกแยกแยกกระบวนการ ไพโรไลซีสแบบช้าเงื่อนไขที่ช้า และไพโรไลซิสแบบเร็วค่อนข้างเผด็จการและไม่แม่นยำกำหนด หลาย pyrolyses มีการปฏิบัติอยู่ในอัตราที่ไม่ " รวดเร็ว " หรือ " ช้า " แต่ในช่วงกว้างระหว่างสุดขั้วเหล่านี้ จุดที่สำคัญคือ หรือไม่ไอและส่วนประกอบสเปรย์อย่างรวดเร็วจะเอาออกเพื่อเพิ่มประสิทธิภาพการสร้างของเหลว ( ไพโรอย่างรวดเร็วแฟลชสูญญากาศไพโรไลซีส ) หรืออยู่ในการติดต่อกับของแข็งได้รับปฏิกิริยาทุติยภูมิซึ่งผลิตเพิ่มปริมาณของแข็งที่ประกอบด้วยคาร์บอน . พารามิเตอร์ปฏิบัติการเพื่อช้าและเร็วเพื่อ biochars ไพโรไลซิสจะสั้น ๆกล่าวถึงด้านล่าง
การแปล กรุณารอสักครู่..