Scale deposition is a difficulty encountered with water-containing ions of insoluble
salts, such as CaCO3, CaSO4, Ca3(PO4)2, Mg(OH)2, silica, and so on [1–4]. With
respect to one or more over-saturated slightly soluble salts, supersaturation may
result in the process of scale precipitation. To prevent or reduce the scale deposition,
the most effective way is to add scale inhibitor [5].
In recent years, polymeric scale inhibitors have been widely used in cooling water
recirculation for their remarkable chelating and dispersion characteristics. Organic
phosphate scale inhibitors, such as 1-hydroxy ethylidene-1, 1-diphosphonic acid
(HEDP), 1-hydroxy ethylidine-1, thiomorpholin-4-ylmethyl-phosphonic acid (TMPA)
and hexa methylene diamine tetra methyl-phosphonic acid (HMDTMP) are used to
prevent mineral films on metallic corrosion [6–8]. However, phosphorous products can
cause serious environmental problems. They are likely to decompose and form
orthophosphoric acid with the increase of temperature, which may cause red tides [9].
Recently, Fengxian Qiu reported a novel non-phosphorus scale inhibitor, b-cyclodextrins
(b-CD) polymer scale inhibitor, which was more environmental friendly [10].
However, it is quite difficult to test b-CD polymers in a traditional way because
there is no tracer active component in it. Improper feed rate of treating medication
may cause serious problems and it is difficult to monitor and control the feed rate of
various water treatment agents. The concentration of fluorescent tracer can be directly
measured by radiation with a calibration curve of tracer concentration. Water-soluble
fluorescent tracer is an environmental product and accessible at a low cost [11].
At present, fluorophores in fluorescent monomer usually contain benzene rings or are
heterocyclic, and their structures are rigid and planar [12]. Therefore, the fluorescent
chromophores are hydrophobic, and the process of preparation of a water-soluble
fluorescent copolymer is difficult. Liu et al. [13] prepared a fluorescent polymer containing
2, 6-bis (2-thienyl) pyridine moieties with reverse microemulsion. Hogen-Esch [14]
reported a water-soluble polymer of poly (9, 9-dihexyl-2, 7-fluorenediyl) (PFH) containing
chromophores such as perylene, coumarin 6, andNile red by micellar copolymerization in
aqueous solution. Hence, it is obvious that water-soluble fluorescent monomer and
aqueous solution polymerization are necessary to prepare fluorescent-tagged copolymer.
In this paper, a water-soluble maleic anhydride-b-cyclodextrins (b-CD–MA) was
obtained via the reaction of b-CD and maleic anhydride (MA). Then, a novel
copolymer scale inhibitor b-CD–MA–AA–PA was synthesized with b-CD–MA,
acrylic acid (AA) and 8-hydroxy-1, 3, 6-pyrenetrisulfonic acid trisodium salt (PA)
as monomers, water as solvent and ammonium persulfate as initiator by aqueous
free-radical polymerization, and it was non-toxic and low cost.
ขนาดสะสมเป็นปัญหาในการพบกับน้ำที่ประกอบด้วยประจุไม่ละลายsalts เช่น CaCO3, CaSO4, Ca3 (PO4) 2, Mg (OH) 2 ซิลิก้า และอื่น ๆ [1-4] ด้วยเคารพหนึ่ง หรือเพิ่มเติมเกินอิ่มตัวเกลือละลายน้ำได้เล็กน้อย supersaturation อาจผลกำลังขนาดฝน เพื่อป้องกัน หรือลดระดับสะสมประสิทธิภาพที่สุดคือการ เพิ่มขนาดผล [5]ในปีที่ผ่านมา inhibitors เครื่องชั่งชนิดได้ถูกใช้ในการระบายน้ำrecirculation สำหรับลักษณะ chelating และแพร่กระจายความโดดเด่น อินทรีย์ฟอสเฟตอัตรา inhibitors เช่น 1 hydroxy ethylidene-1, 1 diphosphonic กรด(HEDP), 1-hydroxy ethylidine-1, thiomorpholin-4-ylmethyl-phosphonic กรด (TMPA)และใช้ hexa เมทิลีนได diamine tetra methyl phosphonic กรด (HMDTMP)ป้องกันฟิล์มแร่ในการกัดกร่อนโลหะ [6-8] อย่างไรก็ตาม phosphorous ผลิตภัณฑ์สามารถทำให้เกิดปัญหาสิ่งแวดล้อมอย่างจริงจัง พวกเขามักจะเปื่อย และแบบฟอร์มกรด orthophosphoric กับการเพิ่มขึ้นของอุณหภูมิ ซึ่งอาจทำให้เกิดกระแสน้ำแดง [9]ล่าสุด คูเฟิงเสียนรายงานนวนิยายไม่มีฟอสฟอรัสระดับสารยับยั้ง บี-cyclodextrins(b-CD) พอลิเมอร์ขนาดสารยับยั้ง ซึ่งเป็นมิตรกับสิ่งแวดล้อมเพิ่มมากขึ้น [10]อย่างไรก็ตาม ก็ค่อนข้างยากที่จะทดสอบโพลิเมอร์บีซีดีแบบดั้งเดิมเนื่องจากยังมีส่วนประกอบไม่ใช้ติดตามใน อัตราการใช้ยารักษาอาหารไม่เหมาะสมอาจทำให้เกิดปัญหาร้ายแรง และยากต่อการตรวจสอบ และควบคุมอัตราการตัวดึงข้อมูลหน้าที่บำบัดน้ำต่าง ๆ ได้อย่างเข้มข้นติดตามเรืองแสงโดยตรงวัด โดยรังสีโค้งเทียบของติดตามความเข้มข้น ที่ละลายในติดตามเรืองแสงเป็นผลิตภัณฑ์สิ่งแวดล้อมและที่มีต้นทุนต่ำ [11]ปัจจุบัน fluorophores ในน้ำยาเรืองแสงมักจะประกอบด้วยวงแหวนเบนซีน หรือเป็น๔๒๓ และโครงสร้างของพวกเขาจะแข็ง และระนาบ [12] ดังนั้น ฟลูออเรสเซนต์chromophores เป็น hydrophobic และกระบวนการในการเตรียมตัวที่ละลายในโคพอลิเมอร์ที่เรืองแสงได้ยาก หลิว et al. [13] เตรียมพอลิเมอร์ที่เรืองแสงที่ประกอบด้วย2, moieties pyridine 6-bis (2 thienyl) กับ microemulsion ย้อน Hogen-Esch [14]รายงานพอลิเมอร์ที่ละลายในของโพลี (9, 9-dihexyl-2, 7-fluorenediyl) (PFH) ประกอบด้วยchromophores เพอรีลีน coumarin 6, andNile สีแดง โดย copolymerization micellar ในละลาย ดังนั้น มันเป็นที่ชัดเจนว่าน้ำยาเรืองแสงที่ละลายใน และpolymerization ละลายจำเป็นในการเตรียมโคพอลิเมอร์ที่ติดแท็กฟลูออเรสเซนต์ในเอกสารนี้ มีแบบที่ละลายใน maleic anhydride-บี-cyclodextrins (b-CD – MA)รับผ่านปฏิกิริยาของบีซีดีและ maleic anhydride (MA) แล้ว นวนิยายมีสังเคราะห์โคพอลิเมอร์ขนาดผล b-CD – MA – AA – PA กับบี-CD – MAกรดอะคริลิค (AA) และ 8-hydroxy-1, 3, 6-pyrenetrisulfonic กรดเกลือ trisodium (PA)เป็น monomers น้ำเป็นตัวทำละลายและแอมโมเนีย persulfate เป็นอุปกรณ โดยอควีอนุมูลอิสระ polymerization และมันเป็นพิษ และต้นทุนต่ำ
การแปล กรุณารอสักครู่..

Scale deposition is a difficulty encountered with water-containing ions of insoluble
salts, such as CaCO3, CaSO4, Ca3(PO4)2, Mg(OH)2, silica, and so on [1–4]. With
respect to one or more over-saturated slightly soluble salts, supersaturation may
result in the process of scale precipitation. To prevent or reduce the scale deposition,
the most effective way is to add scale inhibitor [5].
In recent years, polymeric scale inhibitors have been widely used in cooling water
recirculation for their remarkable chelating and dispersion characteristics. Organic
phosphate scale inhibitors, such as 1-hydroxy ethylidene-1, 1-diphosphonic acid
(HEDP), 1-hydroxy ethylidine-1, thiomorpholin-4-ylmethyl-phosphonic acid (TMPA)
and hexa methylene diamine tetra methyl-phosphonic acid (HMDTMP) are used to
prevent mineral films on metallic corrosion [6–8]. However, phosphorous products can
cause serious environmental problems. They are likely to decompose and form
orthophosphoric acid with the increase of temperature, which may cause red tides [9].
Recently, Fengxian Qiu reported a novel non-phosphorus scale inhibitor, b-cyclodextrins
(b-CD) polymer scale inhibitor, which was more environmental friendly [10].
However, it is quite difficult to test b-CD polymers in a traditional way because
there is no tracer active component in it. Improper feed rate of treating medication
may cause serious problems and it is difficult to monitor and control the feed rate of
various water treatment agents. The concentration of fluorescent tracer can be directly
measured by radiation with a calibration curve of tracer concentration. Water-soluble
fluorescent tracer is an environmental product and accessible at a low cost [11].
At present, fluorophores in fluorescent monomer usually contain benzene rings or are
heterocyclic, and their structures are rigid and planar [12]. Therefore, the fluorescent
chromophores are hydrophobic, and the process of preparation of a water-soluble
fluorescent copolymer is difficult. Liu et al. [13] prepared a fluorescent polymer containing
2, 6-bis (2-thienyl) pyridine moieties with reverse microemulsion. Hogen-Esch [14]
reported a water-soluble polymer of poly (9, 9-dihexyl-2, 7-fluorenediyl) (PFH) containing
chromophores such as perylene, coumarin 6, andNile red by micellar copolymerization in
aqueous solution. Hence, it is obvious that water-soluble fluorescent monomer and
aqueous solution polymerization are necessary to prepare fluorescent-tagged copolymer.
In this paper, a water-soluble maleic anhydride-b-cyclodextrins (b-CD–MA) was
obtained via the reaction of b-CD and maleic anhydride (MA). Then, a novel
copolymer scale inhibitor b-CD–MA–AA–PA was synthesized with b-CD–MA,
acrylic acid (AA) and 8-hydroxy-1, 3, 6-pyrenetrisulfonic acid trisodium salt (PA)
as monomers, water as solvent and ammonium persulfate as initiator by aqueous
free-radical polymerization, and it was non-toxic and low cost.
การแปล กรุณารอสักครู่..

สะสมชั่งเป็นยากพบน้ำที่มีไอออนของเกลือที่ไม่ละลาย
เช่น CaCO3 , การระเบิด ca3 ( po4 ) 2 , Mg ( OH ) 2 , ซิลิกา , และอื่นๆ [ 1 - 1 ] กับ
เคารพหนึ่งหรือมากกว่าไขมันอิ่มตัวต่ำ อาจละลายเล็กน้อย เกลือ ในกระบวนการตกตะกอน
ผลขนาด เพื่อป้องกันหรือลดขนาดสะสม ,
วิธีที่มีประสิทธิภาพมากที่สุดคือการเพิ่มระดับสาร
[ 5 ]ใน ปี ล่าสุด ระดับสารยับยั้งได้รับอย่างกว้างขวางใช้ในการหมุนเวียนน้ำหล่อเย็นและที่น่าทึ่งของพวกเขาสำหรับ
และลักษณะการกระจาย สารยับยั้งระดับฟอสเฟตอินทรีย์ เช่น 1-hydroxy ethylidene-1
,
( 1-diphosphonic กรด hedp ) 1-hydroxy ethylidine-1 thiomorpholin-4-ylmethyl-phosphonic ( tmpa )
, กรดเมทิลีนไดอะมีนเตตระเมทิลเฮกซ่าและต่อกรด ( hmdtmp ) จะถูกใช้เพื่อป้องกันการกัดกร่อนโลหะแร่บนฟิล์ม
[ 6 – 8 ] อย่างไรก็ตาม ผลิตภัณฑ์ฟอสฟอรัสสามารถ
เพราะปัญหาสิ่งแวดล้อมที่ร้ายแรง พวกเขามีแนวโน้มที่จะสลายตัวและแบบฟอร์ม
ออร์โธฟอสฟอริกแอซิดด้วยการเพิ่มของอุณหภูมิ ซึ่งอาจทำให้เกิดกระแสน้ำแดง [ 9 ] .
เมื่อเร็ว ๆนี้ , Fengxian ชิวรายงานนวนิยายไม่ใช่ฟอสฟอรัสระดับสารยับยั้ง b-cyclodextrins
(b-CD) polymer scale inhibitor, which was more environmental friendly [10].
However, it is quite difficult to test b-CD polymers in a traditional way because
there is no tracer active component in it. Improper feed rate of treating medication
may cause serious problems and it is difficult to monitor and control the feed rate of
various water treatment agents. The concentration of fluorescent tracer can be directly
measured by radiation with a calibration curve of tracer concentration. Water-soluble
fluorescent tracer is an environmental product and accessible at a low cost [11].
At present, fluorophores in fluorescent monomer usually contain benzene rings or are
heterocyclic, and their structures are rigid and planar [12]. Therefore, the fluorescent
chromophores are hydrophobic, and the process of preparation of a water-soluble
fluorescent copolymer is difficult. Liu et al. [13] prepared a fluorescent polymer containing
2, 6-bis (2-thienyl) pyridine moieties with reverse microemulsion. Hogen-Esch [14]
reported a water-soluble polymer of poly (9, 9-dihexyl-2, 7-fluorenediyl) (PFH) containing
chromophores such as perylene, coumarin 6, andNile red by micellar copolymerization in
aqueous solution. Hence, it is obvious that water-soluble fluorescent monomer and
aqueous solution polymerization are necessary to prepare fluorescent-tagged copolymer.
In this paper, a water-soluble maleic anhydride-b-cyclodextrins (b-CD–MA) was
obtained via the reaction of b-CD and maleic anhydride (MA). Then, a novel
ที่มีขนาดและ b-cd ––– AA มาป่าสังเคราะห์กับ b-cd – MA
กรดอะคริลิก ( AA ) และ 8-hydroxy-1 , 3 , 6-pyrenetrisulfonic กรดไตรโซเดียมเกลือ ( PA )
เป็นโมโนเมอร์ น้ำ เป็นตัวทำละลาย และ แอมโมเนียมเปอร์ซัลเฟต เป็นผู้ริเริ่ม โดยน้ำ
สารอนุมูลอิสระ และยังปลอดสารพิษ
ราคาถูก
การแปล กรุณารอสักครู่..
