CARBURIZING
Carburizing is a process used to harden low carbon steels that normally would not respond to quenching and tempering. This is done for economical reasons (utilizing less expensive steel) or design considerations to provide a tough part with good wear characteristics. Carburizing introduces carbon into a solid ferrous alloy by heating the metal in contact with a carbonaceous material to a temperature above the transformation range and holding at that temperature. The depth of penetration of carbon is dependent on temperature, time at temperature, and the composition of the carburizing agent. As a rough indication, a carburized depth of about .0.030 to 0.050 inches can be obtained in about 4 hours at 1700°F, depending upon the type of carburizing agent, which may be a solid, liquid, or gas. Since the primary object of carburizing is to secure a hard case and a relatively soft, tough core, only low-carbon steels (up to a maximum of about 0.25% carbon), either with or without alloying elements (nickel, chromium, manganese, molybdenum), are normally used. After carburizing, the steel will have a high carbon case graduating into the low-carbon core. Once the carburization is complete, the parts must be hardened and tempered to obtain the desired properties of both the core and the case.
Carburizing
Carburizing คือกระบวนการที่ใช้แข็งเหล็กกล้าคาร์บอนต่ำที่ปกติจะไม่ตอบสนองต่อการดับและการ . นี้จะกระทำด้วยเหตุผลประหยัด ( ใช้เหล็กราคาไม่แพง ) หรือพิจารณาในการออกแบบเพื่อให้ยากที่สุด มีลักษณะใส่ดีCarburizing เหล็กอัลลอยคาร์บอนในตัวแข็งโดยความร้อนโลหะสัมผัสกับวัสดุที่ประกอบด้วยคาร์บอนให้อุณหภูมิสูงกว่าช่วงการเปลี่ยนแปลง และเก็บไว้ในที่อุณหภูมิ ความลึกของคาร์บอนจะขึ้นอยู่กับอุณหภูมิ เวลาที่อุณหภูมิและองค์ประกอบของ Carburizing ตัวแทน เป็นข้อบ่งชี้ที่ขรุขระ , carburized ความลึกประมาณ . 0.030 0050 นิ้วได้ใน 4 ชั่วโมง ที่ 1700 ° F , ขึ้นอยู่กับชนิดของ Carburizing แทน ซึ่งอาจเป็นก๊าซ ของแข็ง ของเหลว หรือ ตั้งแต่วัตถุหลักของ Carburizing เพื่อรักษากรณียากและค่อนข้างเหนียวนุ่ม แกนเหล็กกล้าคาร์บอนต่ำ ( สูงสุดประมาณ 0.25 % คาร์บอน ) มีหรือไม่มีธาตุอัลลอยด์ ( นิกเกิล , โครเมียม , แมงกานีส , โมลิบดีนัม )โดยปกติจะใช้ หลังจาก Carburizing , เหล็กคาร์บอนสูงจะมีกรณีจบการศึกษาใน - หลัก เมื่อคาร์บูไรเซชันที่สมบูรณ์ ส่วนจะต้องแข็งและนิสัยเพื่อให้ได้คุณสมบัติที่ต้องการของทั้งหลักและกรณี
การแปล กรุณารอสักครู่..