2.1.3 Paraffin Templates
Poly(vinyl alcohol) (PVA) (86.7–88.7% hydrolyzed, average molecular weight of 31,000) was purchased from Sigma Aldrich (Switzerland), and paraffin with a melting point of 56–58C was purchased from Panreac (Barcelona, Spain) and used as received. As previously described in the literature [25], for the preparation of paraffin microspheres a hot plate with magnetic stirring system was used as the heat source. A 1000mL glass bottle with 500mL water was heated to 60–70C. PVA (2.5g) was added with stirring to make a 0.5% w=v solution. 20g paraffin were heated to melt in a glass vial on the same hot plate. After adjusting the stirring speed, paraffin was added to the PVA solution. The mixture was then poured into a big beaker with 2000mL cold water to solidify the paraffin microspheres. Standard sieves (50, 100, and 355mm) were piled up from bottom to up in the previous order. The paraffin microspheres suspension was poured into the sieve tower. After the paraffin microspheres were rinsed with water to remove the residual PVA, they were separated further into two different size ranges: 100–355mm and higher than 355mm. Finally, paraf-fin microspheres were washed with distilled water five times and then lyophilized overnight. To prepare the paraffin tem-plates, plastic syringes (5mL) were chosen as the mould of the paraffin template. The end of the syringe was cut off. To obtain a paraffin template of about 3mm high, the piston was pulled to leave a gap of 3mm between the piston and the syringe end. Paraffin microspheres were transferred to fill the gap. The syringe end was pressed vertically on a piece of glass plate. The piston was pushed down gently to avoid deforming the paraffin microspheres in the process. The whole paraffin template was pushed out by the piston and stored into a desiccator.
2.1.3 Paraffin แม่Poly(vinyl alcohol) (PVA) (86.7–88.7% hydrolyzed, average molecular weight of 31,000) was purchased from Sigma Aldrich (Switzerland), and paraffin with a melting point of 56–58C was purchased from Panreac (Barcelona, Spain) and used as received. As previously described in the literature [25], for the preparation of paraffin microspheres a hot plate with magnetic stirring system was used as the heat source. A 1000mL glass bottle with 500mL water was heated to 60–70C. PVA (2.5g) was added with stirring to make a 0.5% w=v solution. 20g paraffin were heated to melt in a glass vial on the same hot plate. After adjusting the stirring speed, paraffin was added to the PVA solution. The mixture was then poured into a big beaker with 2000mL cold water to solidify the paraffin microspheres. Standard sieves (50, 100, and 355mm) were piled up from bottom to up in the previous order. The paraffin microspheres suspension was poured into the sieve tower. After the paraffin microspheres were rinsed with water to remove the residual PVA, they were separated further into two different size ranges: 100–355mm and higher than 355mm. Finally, paraf-fin microspheres were washed with distilled water five times and then lyophilized overnight. To prepare the paraffin tem-plates, plastic syringes (5mL) were chosen as the mould of the paraffin template. The end of the syringe was cut off. To obtain a paraffin template of about 3mm high, the piston was pulled to leave a gap of 3mm between the piston and the syringe end. Paraffin microspheres were transferred to fill the gap. The syringe end was pressed vertically on a piece of glass plate. The piston was pushed down gently to avoid deforming the paraffin microspheres in the process. The whole paraffin template was pushed out by the piston and stored into a desiccator.
การแปล กรุณารอสักครู่..
ทาง paraf จึง N แม่แบบ
พอลิไวนิลแอลกอฮอล์ ( PVA ) ( 86.7 – 88.7 % ไฮโดรไลซ์ และน้ำหนักโมเลกุลเฉลี่ย 31 , 000 ) ซื้อมาจากซิกม่า Aldrich ( สวิตเซอร์แลนด์ ) , และ paraf จึง N กับจุดหลอมเหลว 56 – 58c ซื้อมาจาก panreac ( บาร์เซโลนา , สเปน ) และใช้เป็น ที่ได้รับ ตามที่อธิบายไว้ก่อนหน้านี้ในวรรณคดี [ 25 ]สำหรับการเตรียมการของ paraf จึง N และร้อนจานแม่เหล็กกวนระบบถูกใช้เป็นแหล่งความร้อน . เป็นขวดแก้วที่มีน้ำ 1000ml 500ml ให้ความร้อน 60 – 70c . PVA ( 2.5G ) คือ เพิ่มด้วย กวนให้ 0.5% w = ปริมาตรสารละลาย ทา paraf จึง n มีค่าความร้อนจะละลายในขวดแก้วเล็กๆ ในจานเดียวกัน หลังจากปรับกวนที่ความเร็ว paraf จึง N ถูกเพิ่มเข้าไป PVA โซลูชั่นผสมแล้วเทลงในบีกเกอร์ที่มีขนาดใหญ่ 2000ml น้ำเย็นที่จะแข็ง paraf จึง N ไมโครสเฟียร์ ตะแกรงมาตรฐาน ( 50 , 100 , และ 355mm ) ถูกซ้อนขึ้นจากด้านล่างขึ้นในลำดับก่อนหน้า การ paraf จึงถูกระงับ N และเทใส่ตะแกรง ทาวเวอร์ หลังจาก paraf N ไมโครสเฟียร์จึงล้างด้วยน้ำเพื่อเอา PVA ที่ตกค้างพวกเขาแยกกันเป็นสองขนาดแตกต่างกันและช่วง : 355mm 100 ) และสูงกว่า 355mm . ในที่สุด paraf - N ไมโครสเฟียร์จึงล้างด้วยน้ำกลั่นจึงได้ครั้งแล้วแห้งข้ามคืน เตรียม paraf จึง N เต็มจาน , เข็มฉีดยาพลาสติก ( 5ml ) ได้รับเลือกเป็นแม่พิมพ์ของ paraf จึง N แม่แบบ ปลายเข็มที่ถูกตัดออก ได้รับ paraf จึง N แม่แบบประมาณ 3mm สูงลูกสูบถูกดึงออกจากช่องว่างระหว่างลูกสูบ และเข็มที่ 3 จบ paraf จึงถูกโอนย้ายไป N และจึงจะลดช่องว่าง เข็มปลายคือกดแนวตั้งบนแผ่นจานแก้ว ลูกสูบถูกดันลงเบา ๆเพื่อหลีกเลี่ยงการ เปลี่ยนรูป ที่ paraf จึง N และในกระบวนการ จึง paraf ทั้งหมด n แม่แบบถูกผลักออกโดยลูกสูบ และเก็บไว้เป็นเดซิกเคเตอร์ .
การแปล กรุณารอสักครู่..