Dear K.Suksan,
Please send me your daily utility report for May and daily WWTP report.
Your anaerobic sludge is dispersed and buoyant, less dense and looks no formation of granules yet. This could mean the following:
1. You have many solids going inside your MUR.
2. Your anaerobic sludge did not grow fast due to coating effect of solids, less digestion of food less grow. Effect is higher VFA and low MUR removal efficiency.
Please do the following:
1. Try to control the TSS below your ET specs.
2. Try to remove more yeast from your decanted beer before dumping to WWTP.
3. Follow up QA for presence of filter aid in your WWTP.
4. Increase upflow velocity of your MUR by increasing the current flow rate of recycling pump by 30 to 40% for 6 months.
- it is expected that the contact time (retention time) of waste water to your anaerobic
sludge will be reduced. The MUR removal efficiency will also reduce and VFA / MUR
effluent COD will increase.
- you may notice bulking at the top of your MUR, which means that you have effectively
remove the solids inside your MUR when you increase your upflow velocity. But observe
if there are sludge being carried out when you increase your upflow velocity.
-another effect of increasing the upflow velocity is you will experience momentarily an
increase in VFA or MUR effluent COD. your final effluent COD and BOD will increase
also, and may be higher than the standard. do not panic when this happens because
we know that we do something to improve our MUR. this will happen not too long. this
is just a short term effect. you may want to inform K.Sukit and your government that we expect an increase in BOD (as read in your BOD on line) and explain to them our action plans (as stated above). this is just a sacrificial move in order to improve our system.
-the long term effect when the solids that binds your anaerobic sludge is removed, will
be better growth rate of slugdge, better digestion and removal of pollutants in your waste water, lower final effluent COD and BOD.
-but you must monitor closely the anearobic sludge on a weekly basis. please send
me weekly analysis of the following when you have started to increase your upflow
velocity:
1. SV 1 hour from SP 1 to SP6.
2. MLSS and MLVSS of:
SP1, SP2, SP3, SP4, SP5, SP6.
-send me also daily report of your waste water parameters so I can help to evaluate
the performance of your wwtp.
See you in June.. Regards,
Dear K.Suksan, Please send me your daily utility report for May and daily WWTP report. Your anaerobic sludge is dispersed and buoyant, less dense and looks no formation of granules yet. This could mean the following: 1. You have many solids going inside your MUR. 2. Your anaerobic sludge did not grow fast due to coating effect of solids, less digestion of food less grow. Effect is higher VFA and low MUR removal efficiency. Please do the following: 1. Try to control the TSS below your ET specs.2. Try to remove more yeast from your decanted beer before dumping to WWTP.3. Follow up QA for presence of filter aid in your WWTP.4. Increase upflow velocity of your MUR by increasing the current flow rate of recycling pump by 30 to 40% for 6 months. - it is expected that the contact time (retention time) of waste water to your anaerobic sludge will be reduced. The MUR removal efficiency will also reduce and VFA / MUR effluent COD will increase. - you may notice bulking at the top of your MUR, which means that you have effectively remove the solids inside your MUR when you increase your upflow velocity. But observe if there are sludge being carried out when you increase your upflow velocity. -another effect of increasing the upflow velocity is you will experience momentarily an increase in VFA or MUR effluent COD. your final effluent COD and BOD will increase also, and may be higher than the standard. do not panic when this happens because we know that we do something to improve our MUR. this will happen not too long. this is just a short term effect. you may want to inform K.Sukit and your government that we expect an increase in BOD (as read in your BOD on line) and explain to them our action plans (as stated above). this is just a sacrificial move in order to improve our system. -the long term effect when the solids that binds your anaerobic sludge is removed, will be better growth rate of slugdge, better digestion and removal of pollutants in your waste water, lower final effluent COD and BOD. -but you must monitor closely the anearobic sludge on a weekly basis. please send me weekly analysis of the following when you have started to increase your upflow velocity: 1. SV 1 hour from SP 1 to SP6. 2. MLSS and MLVSS of: SP1, SP2, SP3, SP4, SP5, SP6. -send me also daily report of your waste water parameters so I can help to evaluate the performance of your wwtp. See you in June.. Regards,
การแปล กรุณารอสักครู่..

เรียน K.Suksan, โปรดส่งรายงานประจำวันของคุณยูทิลิตี้สำหรับเดือนพฤษภาคมและรายงานประจำวัน WWTP. ตะกอนเพาะกายของคุณจะแยกย้ายกันไปและลอยตัวหนาแน่นน้อยและมีลักษณะการก่อตัวของเม็ดยังไม่มี ซึ่งอาจหมายถึงต่อไปนี้: 1 คุณมีของแข็งหลายไปภายใน MUR ของคุณ. 2 กากตะกอนเพาะกายของคุณไม่ได้เติบโตอย่างรวดเร็วเนื่องจากผลการเคลือบผิวของของแข็งการย่อยอาหารน้อยกว่าของอาหารน้อยเติบโต ผลกระทบสูงและต่ำ VFA MUR ประสิทธิภาพในการกำจัด. โปรดทำต่อไปนี้: 1 พยายามที่จะควบคุมรายละเอียดด้านล่าง TSS ET ของคุณ. 2 พยายามที่จะเอายีสต์เพิ่มเติมจากเบียร์ decanted ของคุณก่อนที่จะทิ้ง WWTP. 3 ติดตามควบคุมการปรากฏตัวของความช่วยเหลือกรองใน WWTP ของคุณ. 4 เพิ่มความเร็วไหลของ MUR ของคุณโดยการเพิ่มอัตราการไหลของกระแสของเครื่องสูบน้ำรีไซเคิลโดย 30-40% เป็นเวลา 6 เดือน. - เป็นที่คาดหวังว่าเวลาที่ติดต่อ (การเก็บรักษาเวลา) น้ำเสียที่จะไม่ใช้ออกซิเจนของตะกอนจะลดลง ประสิทธิภาพในการกำจัด MUR ยังจะช่วยลดและ VFA / MUR น้ำเสียซีโอดีจะเพิ่มขึ้น. - คุณอาจสังเกตเห็นการเปรียบเทียบที่ด้านบนของ MUR ของคุณซึ่งหมายความว่าคุณได้อย่างมีประสิทธิภาพลบของแข็งภายใน MUR ของคุณเมื่อคุณเพิ่มความเร็วไหลของคุณ แต่สังเกตว่ามีตะกอนที่ถูกดำเนินการเมื่อคุณเพิ่มความเร็วไหลของคุณ. -another ผลกระทบของการเพิ่มความเร็วไหลคือคุณจะได้สัมผัสชั่วขณะการเพิ่มขึ้นของ VFA หรือ MUR น้ำเสียซีโอดี ซีโอดีของน้ำทิ้งขั้นสุดท้ายของคุณและคณะกรรมการ บริษัท จะเพิ่มขึ้นด้วยและอาจจะสูงกว่ามาตรฐาน ไม่ต้องตกใจเมื่อสิ่งนี้เกิดขึ้นเพราะเรารู้ว่าเราทำอะไรเพื่อปรับปรุง MUR ของเรา นี้จะเกิดขึ้นไม่นาน นี้เป็นเพียงผลกระทบระยะสั้น คุณอาจต้องการที่จะแจ้งให้ K.Sukit และรัฐบาลของคุณที่เราคาดว่าการเพิ่มขึ้นของค่าบีโอดี (ตามที่อ่านในที่ประชุมคณะกรรมการของคุณในบรรทัด) และอธิบายให้พวกเขาแผนปฏิบัติการของเรา (ตามที่ระบุไว้ข้างต้น) นี้เป็นเพียงการย้ายเสียสละเพื่อที่จะปรับปรุงระบบของเรา. -THE ผลกระทบระยะยาวเมื่อของแข็งที่ผูกตะกอนเพาะกายของคุณจะถูกลบออกจะเป็นอัตราการเติบโตที่ดีขึ้นของ slugdge การย่อยอาหารดีขึ้นและการกำจัดของสารมลพิษในน้ำเสียของคุณลดลงเป็นครั้งสุดท้าย น้ำเสียซีโอดีและบีโอดี. -but คุณต้องตรวจสอบอย่างใกล้ชิดตะกอน anearobic เป็นประจำทุกสัปดาห์ กรุณาส่งฉันวิเคราะห์รายสัปดาห์ต่อไปนี้เมื่อคุณได้เริ่มต้นที่จะเพิ่มการไหลของคุณความเร็ว: 1 SV 1 ชั่วโมงจาก SP 1 ถึง SP6. 2 MLSS และ MLVSS ของ: . SP1, SP2, SP3, SP4, SP5, SP6 -send ฉันยังรายงานประจำวันของพารามิเตอร์น้ำเสียของคุณเพื่อให้ฉันสามารถช่วยในการประเมิน. ประสิทธิภาพการทำงานของ WWTP คุณเห็นคุณในเดือนมิถุนายน .. ขอแสดงความนับถือ
การแปล กรุณารอสักครู่..

ที่รัก สุขสันต์
K , โปรดส่งรายงานสาธารณูปโภคของคุณทุกวันสำหรับอาจและรายงาน wwtp ทุกวัน
ตะกอนถังของคุณและกระจายตัวน้อยหนาแน่นและดูเหมือนจะไม่ก่อตัวของเม็ดเลย นี้อาจหมายถึงต่อไปนี้ :
1 คุณมีของแข็งหลายเข้าไปกระโดดของคุณ
2 . กากตะกอนบำบัดของคุณไม่เติบโตอย่างรวดเร็ว เนื่องจากการเคลือบผลของของแข็ง การย่อยอาหารน้อยกว่าอาหารน้อยปลูกผลคือ ง่าย และมีประสิทธิภาพในการกำจัดสูงกว่ามูร์น้อย
กรุณาทำต่อไปนี้ :
1 พยายามที่จะควบคุมปริมาณของ TSS ด้านล่างของคุณและรายละเอียด .
2 ลองเอายีสต์เพิ่มเติมจากของคุณรินเบียร์ ก่อนจะทิ้งให้ wwtp .
3 ติดตามสถานะของ QA เพื่อกรองช่วยใน wwtp .
4 เพิ่มความเร็วไหลขึ้นของการกระโดดของคุณ โดยการเพิ่มอัตราการไหลของกระแสรีไซเคิลปั๊มโดย 30 ถึง 40 %
6 เดือนค่ะ- คาดว่าติดต่อเวลา ( เวลาเก็บกักของน้ำเสียในถัง ) ตะกอน
ของคุณจะลดลง ประสิทธิภาพการกำจัด MUR ยังจะลดและลดลงในน้ำทิ้งซีโอจะเพิ่ม / เหม่อ
.
- คุณอาจสังเกตเห็นพะรุงพะรังที่ด้านบนของกระโดดของคุณ ซึ่งหมายความว่าคุณได้อย่างมีประสิทธิภาพ
เอาของแข็งภายในเหม่อของคุณเมื่อคุณเพิ่มความเร็วไหลขึ้นของคุณ แต่สังเกต
หากมีตะกอนถูกนำมาใช้เมื่อคุณเพิ่มความเร็วไหลขึ้นของคุณ .
- อื่นผลของการเพิ่มความเร็วไหลขึ้นเป็นคุณจะพบการลดลงหรือเพิ่มขึ้นในชั่วขณะ
เหม่อ COD น้ำทิ้ง ซีโอดีและบีโอดีของน้ำทิ้งสุดท้ายจะเพิ่ม
ด้วย และอาจจะสูงกว่ามาตรฐาน อย่าตกใจเมื่อนี้เกิดขึ้นเนื่องจาก
เรารู้ว่าเราทำอะไรเพื่อปรับปรุงการกระโดดของเรานี้จะเกิดขึ้น ไม่ยาวเกินไป นี้
เป็นเพียงผลกระทบในระยะสั้น คุณอาจต้องการที่จะแจ้งให้คุณสุกิจและรัฐบาลที่เราคาดว่าการเพิ่มขึ้นของบีโอดี ( BOD ของคุณอ่านบนบรรทัด ) และอธิบายถึงแผนงานของเรา ( ตามที่ระบุไว้ข้างต้น ) นี่เป็นแค่เสียสละย้ายเพื่อปรับปรุงระบบของเรา
- ผลกระทบในระยะยาวเมื่อของแข็งผูกตะกอนถังของคุณจะถูกลบออกจะ
มีอัตราการเติบโตที่ดีขึ้นของ slugdge , การย่อยอาหารดีขึ้นและการกำจัดสารมลพิษในน้ำเสียน้ำทิ้งสุดท้ายของคุณ , ลด COD และ BOD
- แต่คุณจะต้องตรวจสอบอย่างใกล้ชิดของตะกอน anearobic ในสัปดาห์ กรุณาส่ง
ฉันรายสัปดาห์วิเคราะห์ต่อไปนี้เมื่อคุณเริ่มที่จะเพิ่มความเร็วไหลขึ้น
:
1 SV 1 ชั่วโมงจาก SP 1 sp6 .
2 เอสเอ็มแอลวีเอสเอส :
SP1 และ SP2 , SP3 sp4 sp5 , , ,sp6
- ส่งผมทุกวัน รายงานของพารามิเตอร์น้ำเสียของคุณดังนั้นฉันสามารถช่วยประเมินประสิทธิภาพของ wwtp
.
แล้วเจอกันในเดือนมิถุนายน . . . . . . . ขอแสดงความนับถือ
การแปล กรุณารอสักครู่..
