Stupidly enough, Fanuc saw fit to document the boot loader and backup functions in the B-66102E "FAPT MACRO COMPILER for PersonalComputer Operator's Manual". Really. Section G. BOOT SYSTEM (FOR Series 16–B/C,18–B/C, 20, 21–B, 0–A).
Here is (some of) what Section G.2.4. System Data Save Screen says:
(1) Difference between a system file and user file for SYSTEM DATA SAVE
SYSTEM DATA SAVE protects system files so that they cannot be
copied easily. User files are not protected.
(2) Names of saved files
The names of the files written from flash memory to the memory card
are as follows:
Series 21
Flash memory Memory card
NC BASIC NC_BASIC.XXX
DG SERVO DG_SERVO.XXX
NC1 OPTN NC1_OPTN.XXX
PMC-RA PMC–RA.XXX
PCD 128k PCD_128k.XXX
PCD 256k PCD_256k.XXX
PCD 0.5M PCD_0.5M.XXX
PCD 1.0M PCM_1.0M.XXX
XXX is equivalent to the extension assigned to MS-DOS file names.
One of 32 numbers from 000 to 031 is assigned as XXX. For
example, if a PMC-RB file in flash memory is saved to a memory card
containing no PMC_RB.* files, the saved file is named
PMC_RB.000. If that same file is saved to a memory card that
already contains a PMC_RB.000 file, however, it is named
PMC_RB.001. In this way, the extension is incremented by one, up
to PMC_RB.031. If there are any free extension numbers in the
sequence of the extension numbers, they are used in ascending order.
If two or more files having identical names but different extension
numbers are saved to a single memory card, check the file names
displayed after saving. In the case of Serics 20, to write a P-CODE
macro file, with a password assigned by MLINK, from flash memory
to a memory card, the password must be entered. The macro
password is explained in Sec.G.4.
Then there is section G.2.5 SRAM Data Backup, which goes on:
This screen is used for the batch saving and restoring of parameters,
programs, and other data to be retained after the CNC is turned off to/from
a memory card.
Do you have the B-66102E FAPT manual?
I too would like to know how to backup (and restore) everything. That would be a great sticky for the CNC forum.
It is not at all clear to me if some data can only be punched/read over the tape interface.
I am certain that you are a few pages ahead in the homework than me.
Stupidly enough, Fanuc saw fit to document the boot loader and backup functions in the B-66102E "FAPT MACRO COMPILER for PersonalComputer Operator's Manual". Really. Section G. BOOT SYSTEM (FOR Series 16–B/C,18–B/C, 20, 21–B, 0–A).
Here is (some of) what Section G.2.4. System Data Save Screen says:
(1) Difference between a system file and user file for SYSTEM DATA SAVE
SYSTEM DATA SAVE protects system files so that they cannot be
copied easily. User files are not protected.
(2) Names of saved files
The names of the files written from flash memory to the memory card
are as follows:
Series 21
Flash memory Memory card
NC BASIC NC_BASIC.XXX
DG SERVO DG_SERVO.XXX
NC1 OPTN NC1_OPTN.XXX
PMC-RA PMC–RA.XXX
PCD 128k PCD_128k.XXX
PCD 256k PCD_256k.XXX
PCD 0.5M PCD_0.5M.XXX
PCD 1.0M PCM_1.0M.XXX
XXX is equivalent to the extension assigned to MS-DOS file names.
One of 32 numbers from 000 to 031 is assigned as XXX. For
example, if a PMC-RB file in flash memory is saved to a memory card
containing no PMC_RB.* files, the saved file is named
PMC_RB.000. If that same file is saved to a memory card that
already contains a PMC_RB.000 file, however, it is named
PMC_RB.001. In this way, the extension is incremented by one, up
to PMC_RB.031. If there are any free extension numbers in the
sequence of the extension numbers, they are used in ascending order.
If two or more files having identical names but different extension
numbers are saved to a single memory card, check the file names
displayed after saving. In the case of Serics 20, to write a P-CODE
macro file, with a password assigned by MLINK, from flash memory
to a memory card, the password must be entered. The macro
password is explained in Sec.G.4.
Then there is section G.2.5 SRAM Data Backup, which goes on:
This screen is used for the batch saving and restoring of parameters,
programs, and other data to be retained after the CNC is turned off to/from
a memory card.
Do you have the B-66102E FAPT manual?
I too would like to know how to backup (and restore) everything. That would be a great sticky for the CNC forum.
It is not at all clear to me if some data can only be punched/read over the tape interface.
I am certain that you are a few pages ahead in the homework than me.
การแปล กรุณารอสักครู่..
ดูพอ FANUC เห็นพอดีเอกสารตัวโหลดการบูตและฟังก์ชั่นการสำรองข้อมูลในโปรแกรมแมโครในความเป็นจริงที่ b-66102e " คู่มือ " เครื่องคอมพิวเตอร์ของผู้ให้บริการ . จริง ๆ ส่วน จี บูตระบบ ( ชุด 16 – 18 – B / C , B / C , 20 , 21 ) b , 0 ) ) .
ที่นี่คือ ( บางส่วน ) แล้ว ส่วน g.2.4 . ระบบบันทึกข้อมูลที่หน้าจอบอกว่า :
( 1 ) ความแตกต่างระหว่างไฟล์ระบบและไฟล์สำหรับระบบบันทึกข้อมูลผู้ใช้
ระบบข้อมูลช่วยป้องกันไฟล์ระบบเพื่อให้พวกเขาไม่สามารถ
คัดลอกได้อย่างง่ายดาย ไฟล์ของผู้ใช้ที่ไม่มีการป้องกัน .
( 2 ) ชื่อของไฟล์ที่บันทึกไว้
ชื่อของแฟ้มที่เขียนจากความจำแฟลชการ์ดหน่วยความจำ
มีดังนี้
ชุด 21
NC พื้นฐานหน่วยความจำแฟลชการ์ดหน่วยความจำ nc_basic X
DG servo dg_servo X
nc1 optn nc1_optn X
pmc-ra PMC จำกัด รา X
PCD 128k pcd_128k X
PCD 256K pcd_256k X
PCD 0.5 pcd_0.5m .xxx
PCD 1.0m pcm_1.0m X
xxx จะเทียบเท่ากับการได้รับมอบหมายให้ MS-DOS ชื่อไฟล์ .
1 32 ตัวเลขจาก 000 031 มอบหมายเป็น xxx . สำหรับ
ตัวอย่าง ถ้า pmc-rb แฟ้มในหน่วยความจำแฟลชจะถูกบันทึกไว้ในเมมโมรี่การ์ด
ประกอบด้วยไม่ pmc_rb * แฟ้มบันทึกแฟ้มชื่อ
pmc_rb.000 . ถ้าไฟล์เดียวกันที่บันทึกไว้ในการ์ดหน่วยความจำที่
แล้วมีไฟล์ pmc_rb.000 อย่างไรก็ตามมันเป็นชื่อ
pmc_rb .001 . ในวิธีนี้ , การสั่งโดยหนึ่งขึ้นเพื่อ pmc_rb.031
. หากมีตัวเลขการขยายใด ๆฟรีใน
ลำดับของส่วนขยาย ตัวเลข พวกเขาจะใช้ในลําดับ
ถ้าสองคนหรือมากกว่าไฟล์ที่มีชื่อเหมือนกัน แต่ตัวเลขการขยาย
ที่แตกต่างกันจะถูกบันทึกไว้ในการ์ดหน่วยความจำ , ตรวจสอบชื่อไฟล์
แสดงหลังจากการบันทึก ในกรณีของ serics เขียนคางเบือน
20ไฟล์แมโครด้วยรหัสผ่านที่ได้รับมอบหมายจากมลิ้งค์ จาก
หน่วยความจำแฟลชเมมโมรี่การ์ด , รหัสผ่านจะต้องป้อน แมโครรหัสผ่าน
อธิบายในวินาที g.4
แล้วมีมาตรา g.2.5 SRAM สำรองข้อมูลซึ่งไป :
หน้าจอนี้จะใช้สำหรับชุดการบันทึกและการเรียกคืนของพารามิเตอร์
โปรแกรมและข้อมูลอื่น ๆที่จะถูกเก็บไว้หลังจากเครื่องปิด /
การ์ดความจำ
คุณมี b-66102e ที่จริงคู่มือ
ผมก็อยากจะรู้ว่าวิธีการสำรองข้อมูลและเรียกคืน ) ทุกอย่าง มันจะเหนียวมากสำหรับ CNC ฟอรั่ม
มันไม่ได้ทั้งหมดชัดเจนเลย ถ้าข้อมูลบางอย่างสามารถเจาะ / อ่านเทปติดต่อ
ฉันแน่ใจว่า คุณมีไม่กี่หน้าเลยในบ้านมากกว่าฉัน
การแปล กรุณารอสักครู่..