1.Press set buttom for 4 second until LED is all bright then slowly blink. Release the bottom. A slow flashing of LED indicates that the module entered into debug state.
Condition : Light is all bright then slowly blink
2. powering the positioner input signal for 4mA. After the ammeter reaches the setting value,shortly press “set bottom. The system wall automatically enter to the 8mA Position standby mode.
( The “ +”,”-“ Bottom can be used for adjustment. )
Condition : Light is all bright then slowly blink
3. powering the positioner input signal for 8mA. After the ammeter reaches the setting value,shortly press “set bottom. The system wall automatically enter to the 12mA Position standby mode.
( The “ +”,”-“ Bottom can be used for adjustment. )
Condition : Light is all bright then slowly blink
4. powering the positioner input signal for 12mA. After the ammeter reaches the setting value,shortly press “set bottom. The system wall automatically enter to the 16mA Position standby mode.
( The “ +”,”-“ Bottom can be used for adjustment. )
Condition : Light is all bright then slowly blink
5. powering the positioner input signal for 16mA. After the ammeter reaches the setting value,shortly press “set bottom. The system wall automatically enter to the 20mA Position standby mode.
( The “ +”,”-“ Bottom can be used for adjustment. )
Condition : Light is all bright then slowly blink
6. Powering the Positioner input signal for 20mA. After the ammeter reaches the setting velue , shortly press “set” buttom. At this time, LED light will flash for a few time then keep a constant brightness, indicating the adjustment is completed. The system automatically enters normal operating condition.
If the LED light rapidly blinks, indicating the setting is wrong ( Having repeat setting in some steps) , after finish the adjusting process, reset again from the 1st step.
( The “ +”,”-“ Buttom can be used for adjustment. )
Condition : LED Light will flash for a few times
When adjusting the feedback signal, in case the current signal deviation of feedback system is out of the acceptable range, press “+” or “-“ buttom to adjust the current (long press enable for faster adjustment), to meet the current value requirement.
( The “+” , “-“ buttom may be used in the 2nd – 6th step. )
Cautions:
In case of inverting 20mA Input signal to 4mA feedback signal, while the module is waitimg for the confirmation of 4mA Positioner, EP input signal can be adjusted to 20mA. Then 16mA-12mA-8mA-4mA, Until the adjustment is completed.
1.กด buttom ตั้ง 4 วินาทีจนกว่าไฟ LED จะสว่างทั้งหมด นั้นกะพริบช้า ปล่อยด้านล่าง กะพริบช้าของ LED แสดงว่า โมดูลเข้ารัฐดีบัก เงื่อนไข: แสงสว่างทั้งหมด แล้วกะพริบช้า 2. เปิดสัญญาณอินพุต positioner สำหรับ 4mA หลังจาก ammeter ถึงค่าการตั้งค่า ในไม่ช้ากดการ "ตั้งด้านล่าง ผนังระบบป้อนอัตโนมัติไปยังโหมดสแตนด์บายตำแหน่งของ 8mA ("+", "-" ด้านล่างใช้สำหรับการปรับปรุงได้) เงื่อนไข: แสงสว่างทั้งหมด แล้วกะพริบช้า 3. เปิดสัญญาณอินพุต positioner สำหรับ 8mA หลังจาก ammeter ถึงค่าการตั้งค่า ในไม่ช้ากดการ "ตั้งด้านล่าง ผนังระบบป้อนอัตโนมัติไปยังโหมดสแตนด์บายตำแหน่งของ 12mA ("+", "-" ด้านล่างใช้สำหรับการปรับปรุงได้) เงื่อนไข: แสงสว่างทั้งหมด แล้วกะพริบช้า 4. เปิดสัญญาณอินพุต positioner สำหรับ 12mA หลังจาก ammeter ถึงค่าการตั้งค่า ในไม่ช้ากดการ "ตั้งด้านล่าง ผนังระบบป้อนอัตโนมัติไปยังโหมดสแตนด์บายตำแหน่งของ 16mA ("+", "-" ด้านล่างใช้สำหรับการปรับปรุงได้) เงื่อนไข: แสงสว่างทั้งหมด แล้วกะพริบช้า 5. เปิดสัญญาณอินพุต positioner สำหรับ 16mA หลังจาก ammeter ถึงค่าการตั้งค่า ในไม่ช้ากดการ "ตั้งด้านล่าง ผนังระบบป้อนอัตโนมัติไปยังโหมดสแตนด์บายตำแหน่งของ 20mA ("+", "-" ด้านล่างใช้สำหรับการปรับปรุงได้) เงื่อนไข: แสงสว่างทั้งหมด แล้วกะพริบช้า6. เปิดสัญญาณอินพุต Positioner สำหรับ 20mA หลังจาก ammeter ถึง velue การตั้งค่า ในไม่ช้ากด buttom "ตั้ง" ตอนนี้ ไฟ LED จะแฟลชสำหรับกี่ครั้งนั้นให้ความสว่างคงที่ แสดงการปรับปรุงเสร็จสมบูรณ์ ระบบป้อนเงื่อนไขการปฏิบัติงานปกติโดยอัตโนมัติ ถ้าหลอดไฟอย่างรวดเร็วกะพริบ ระบุการตั้งค่าไม่ถูกต้อง (มีทำซ้ำบางขั้นตอนการตั้งค่า), หลังจากเสร็จสิ้นกระบวนการปรับปรุง ตั้งค่าใหม่จากขั้นตอน 1 อีก ("+", "-" Buttom สามารถใช้สำหรับการปรับปรุงได้) เงื่อนไข: ไฟ LED จะกะพริบในกี่ครั้งเมื่อปรับผลป้อนกลับสัญญาณ ในกรณีที่เป็นการเบี่ยงเบนสัญญาณปัจจุบันของระบบความคิดเห็นไม่อยู่ในช่วงยอมรับได้ กด "+" หรือ "-" buttom ปรับปัจจุบัน (ลองกดเปิดใช้งานสำหรับการปรับปรุงเร็ว), เพื่อตอบสนองความต้องการมูลค่าปัจจุบัน ("+", "-" Buttom อาจถูกใช้ในขั้นตอนที่ 2 – 6 ได้) ข้อควรระวัง:ในกรณีของสีตรงกันข้ามสัญญาณอินพุต 20mA กับ 4mA ผลป้อนกลับสัญญาณ โมเป็น waitimg สำหรับการยืนยัน 4mA Positioner, EP สัญญาณอินพุตสามารถปรับเปลี่ยนได้ 20mA แล้ว 16mA-12mA-8mA-4mA จนกว่าการปรับปรุงเสร็จสมบูรณ์
การแปล กรุณารอสักครู่..