discussion3.1. Microstructure characterizationFig. 2 shows the optical microstructures in the different zonesof the DSS joint welded by three different welding techniques.In the DSS (S31803) welding joints, the austenite contains twotypes: primary austenite and 2. The primary austenite are directlysolidified from molten metals among ferritic dendrites as well asformed from the subsequent solid-state phase transition of the fer-rite into the austenite. According to precipitation mechanism andmorphology, the primary austenite are divided into grain bound-ary austenite, Widmanstätten austenite, intragranular austenite,and partially transformed austenite. The allotriomorphic austenitefirst begun to nucleate and grew at prior ferrite boundaries, whichwere named as grain boundary austenite [41,42]. When coolingcontinued and the amount of grain boundary austenite increased,the available nucleation sites at the ferrite boundaries decreasedand then if time permitted, new nuclei begun to initiate from grainboundary austenite, and grew towards the ferrite side in the formof side-plate Widmanstätten austenite [41]. If with sufficient timeafter reheating from subsequent beads, the intragranular austenitecan form at the Ni/N-rich regions in the ferrite grain. The intra-granular austenite formation needs more undercooling as a drivingforce compared to the grain boundary austenite and Widmanstät-ten austenite because of its higher activation energy for latticediffusion, as reported by Eghlimi et al. [42]. Since lattice diffusionoccurs much slower than grain boundary diffusion, the intragran-ular austenite growth is limited, thereby resulting in finer grains,as shown in Fig. 2. The intragranular austenite generally nucleatesat the inclusions and dislocations or other small precipitates such
discussion3.1 . โครงสร้างจุลภาค characterizationfig . 2 แสดงโครงสร้างจุลภาคแสงใน zonesof ต่างร่วมกันโดยทั้งสามต่างเชื่อมใจเชื่อมเทคนิค ในระบบสนับสนุนการตัดสินใจ ( s31803 ) การเชื่อมข้อต่อ , austenite ประกอบด้วยสองประเภท : austenite หลักและ 2 การ austenite หลัก directlysolidified จากโลหะหล่อ กลุ่มเฟอร์ริติกกุยช่ายเช่นกัน asformed จากที่ตามมาของการเปลี่ยนเฟสของเฟอร์ไรต์ใน austenite . ตามด้วย andmorphology กลไก , austenite หลักแบ่งออกเป็นเม็ดผูกเกี่ยวกับ austenite widmanst tten austenite intragranular , การศึกษา , austenite และเปลี่ยนบางส่วน austenite . การ allotriomorphic austenitefirst เริ่ม nucleate และเติบโตในขอบเขตไรท์ก่อน คือ ชื่อ เป็น เม็ด austenite ขอบเขต [ 41,42 ] เมื่อ coolingcontinued และปริมาณของ austenite ขอบเกรนเพิ่มพร้อมขนาดไซต์ที่ไรท์ขอบเขต decreasedand แล้วถ้าเวลาได้รับอนุญาตใหม่ นิวเคลียสเริ่มเริ่มจาก grainboundary austenite และขยายตัวทางด้านเฟอร์ในรูปข้างจาน widmanst และ tten austenite [ 41 ] หากมีเพียงพอ timeafter อุ่นจากต่อมาลูกปัด , intragranular austenitecan ฟอร์มที่ผม / n-rich ภูมิภาคในเฟอร์ไรท์ของเมล็ดข้าว ภายในเม็ด austenite การพัฒนาความต้องการ undercooling เป็น drivingforce เมื่อเทียบกับเม็ดและขอบเขต austenite widmanst ที เทน และ austenite เนื่องจากสูงกว่าพลังงานก่อกัมมันต์สำหรับ latticediffusion , รายงานโดย eghlimi et al . [ 42 ] เนื่องจากตาข่าย diffusionoccurs ช้ากว่าการแพร่ขอบเกรน , intragran ular austenite การเจริญเติบโตมีจำกัด จึงส่งผลให้เม็ดละเอียด ดังแสดงในรูปที่ 2 การ austenite intragranular โดยทั่วไปและ nucleatesat รวมค่าธรรมเนียมหรือตะกอนขนาดเล็กอื่น ๆ เช่น
การแปล กรุณารอสักครู่..
