Figure 9 shows the conductance of various composites
at the same total filler concentration. It was found that
the binary composite of 55 phr carbon black has a higher
conductance than the two ternary composites. This is probably
because both metallic powders contained in ternary
composites do not form the conductive path such as carbon
black alone. Further study with an X-ray diffractometor
(which is not shown here) revealed that there is silver sulfide
(Ag2S) and aluminum oxide (Al2O3) formation in the ternary
composites. That may also cause the reduction of the conductance.
Figure 10 shows the capacitance of the composites
with various loadings of carbon black. At the loading range
of 0-50 phr, the capacitance of the composites slightly
increases due to the slight increase in the number of charge
carriers or electrons. Within the range of 50-55 phr, the gap
between carbon black aggregates is minimal leading to the
drastic increase of the capacitance. At carbon black content
higher than 55 phr, CB agglomerates are locate closely to
others resulting to very high capacitance. Above 55 phr the
capacitance does not change significantly with CB content.
Figure 11 shows the dependence of permittivity on the
excitation frequency and thickness in the frequency range of
100 Hz to 100 kHz. The permittivity decreases with the increasing of frequency. This can be explained on the basis
of a distribution of localized states in the band gap of the
amorphous polymer (Tagmouti et al., 1997) along with the
relationship of permittivity and frequency,
1
f
_ _ . That is, at
low frequency, the energy band gap is wider than at high
frequency. Thus, the capacitance at low frequency is higher
than at high frequency. The permittivity of the composite
specimen with a thickness of 2 mm is slightly higher than the
one with a thickness of 4.5 mm. However, the permittivity of
the specimen with a thickness of 5.5 mm is much lower than
the other two samples. Again, this may described from the
effect of material non-homogeneity as in the case of the
conductivity result.
รูปที่ 9 แสดงความนำไฟฟ้าของวัสดุผสมต่าง ๆขณะ เดียวกัน ปริมาณสารทั้งหมด ผลการวิจัยพบว่าคอมโพสิตไบนารีของ 55 , คาร์บอนสีดำมีสูงกว่าความนำ กว่าสองประกอบไปด้วยคอมโพสิต อาจเป็นแบบนี้เพราะทั้งผงโลหะที่มีอยู่ในพ.ศ.คอมโพสิตไม่ฟอร์มเส้นทางกระแสไฟฟ้า เช่น คาร์บอนดำอยู่คนเดียว การศึกษากับ diffractometor เอ็กซเรย์( ซึ่งไม่ได้แสดงที่นี่ ) พบว่า มีเงินซัลไฟด์( ag2s ) และอลูมิเนียมออกไซด์ ( Al2O3 ) เกิดในพ.ศ.คอมโพสิต ที่อาจก่อให้เกิดการลดลงของความนำ .รูปที่ 10 แสดงความจุของคอมโพสิตด้วยภาระต่าง ๆของคาร์บอนสีดำ โหลดที่หลากหลายของ 0-50 phr , ความจุของคอมเล็กน้อยเพิ่มขึ้นเนื่องจากการเพิ่มจำนวนของค่าเล็กน้อยผู้ให้บริการหรืออิเล็กตรอน ภายในช่วง 50-55 phr , ช่องว่างระหว่างคาร์บอนสีดำมวลรวมน้อยที่สุดนำไปสู่เพิ่มขึ้นอย่างมากของความจุ . ที่ปริมาณคาร์บอนสีดำสูงกว่า 55 phr , CB agglomerates มีอยู่อย่างใกล้ชิดผู้อื่นส่งผลให้ความจุสูงมาก 55 ส่วนการข้างต้นความจุไม่ได้เปลี่ยนแปลงอย่างมีนัยสำคัญกับ CB )รูปที่ 11 แสดงการพึ่งพาอาศัยกันของป้อนในกระตุ้นความถี่ในช่วงความถี่และความหนา100 Hz ถึง 100 กิโลเฮิรตซ์ การป้อนลดลงตามการเพิ่มขึ้นของค่าความถี่ นี้สามารถอธิบายบนพื้นฐานของการเป็นรัฐในช่องว่างแถบของโพลิเมอร์อสัณฐาน ( tagmouti et al . , 1997 ) พร้อมกับความสัมพันธ์ของค่าความซาบซึมและความถี่1เอฟ_ _ . นั่นมันความถี่ต่ำ , วงช่องว่างพลังงานกว้างกว่าที่สูงความถี่ ดังนั้น , ความจุความถี่ต่ำจะสูงขึ้นกว่าที่ความถี่สูง การป้อนของคอมโพสิตชิ้นงานที่มีความหนา 2 มม. เป็นเล็กน้อยสูงกว่าหนึ่งที่มีความหนา 4.5 mm อย่างไรก็ตาม การป้อนของชิ้นงานที่มีความหนา 5.5 มม. ต่ำกว่าอีก 2 คน อีกครั้งนี้อาจอธิบายได้จากผลของวิธีการที่ไม่ใช่วัสดุเช่นในกรณีของผลการนำ
การแปล กรุณารอสักครู่..